The most common reason a light is not working is a blown or failing bulb. If fitting a new bulb of the right type does not fix the problem, the issue lies deeper in the fitting, the switch or the lighting circuit. When a new bulb fails to turn on, or you notice signs such as flickering, crackling, burn marks, a switch that feels warm or a circuit that keeps tripping, switch the light off and call a registered electrician.
Why a light stops working
A household lighting circuit is made up of several connected parts, and a failure in any one of them will leave you in the dark. The electricity travels from your consumer unit, also called a fuse box or fuse board, along concealed cables to the light switches and ceiling fittings. If any component breaks the loop, the electricity cannot reach the bulb.
Common causes of a lighting circuit failure include:
- A failing bulb reaching the end of its lifespan
- A faulty LED lamp or a broken LED driver
- A faulty light fitting or a failing transformer
- A loose connection at a wall switch or ceiling fitting
- Moisture in an outside or bathroom fitting on the same circuit
- A damaged cable, which is less common
If the bulb is intact, the fault may sit within the surrounding hardware. Sometimes the problem is not even in the room where the light has failed, as moisture in an outside fitting on the same circuit can cause a lighting circuit to trip.
Do not remove switches, fittings or the consumer unit cover to investigate these faults. That is work for a registered electrician.
The bulb or lamp
Before you assume there is a fault with the wiring, you should rule out the bulb. Modern bulbs last a long time, but they still fail eventually. If you are dealing with a table or floor lamp, turn the lamp off and unplug it from the wall socket first.
You must wait a few minutes for the light bulb to cool first before attempting to change it. A bulb that has been on can be hot, so give it time to cool.
When you select a replacement, never use a light bulb which is over the recommended power rating for your lamp. The new bulb should be the exact type specified by the manufacturer. The fit of the new bulb into the holder should be perfect, meaning it is not forced into place and does not feel loose once installed.
For ceiling downlights, always switch off the electrical supply before replacing a lamp. Check the packaging and the light fitting for the correct lamp type and the maximum wattage, and ensure you do not exceed that stated rating. You should check downlights regularly for signs of heat damage, such as discolouration, scorching or curled labels, and have any faulty or overheating fittings replaced promptly.
The fitting, switch or driver
When a new bulb of the correct specification does not solve the problem, the fault is likely in the hardware that controls the light. A loose connection at a switch or ceiling fitting is one possible cause, and finding it is a job for an electrician.
LED lighting and downlights may use an LED driver or a transformer. A fault in the driver or transformer is another possible cause, and an electrician diagnoses it.
A faulty light fitting is also a possible cause. If you need a professional to change a light fitting, a registered electrician can diagnose the fault and replace it.
A tripped lighting circuit
If multiple lights go off at the same time but your plug sockets still work, a tripped protective device on your lighting circuit is one possible cause. This happens at your consumer unit, which houses the circuit breakers and safety switches for your home. If a light is switched on and the trip happens immediately, the bulb or the fitting may be faulty.
Many modern consumer units feature a Residual Current Device, commonly known as an RCD, or an RCBO to protect the circuits. Pressing the test button on an RCD will switch off the power to the areas of the home it protects, and this is a safe user level check you can perform regularly. If the test button does not work, you should get a registered electrician to investigate the unit.
If your RCD keeps tripping, there is likely to be a fault that needs investigating. This fault could be in a particular appliance or within the hidden wiring of your house. You should get a registered electrician to investigate why your electricity keeps tripping, as they can advise on a solution and carry out any work needed.
Do not try to find or fix a tripping fault yourself. One council's advice for an older fuse board rather than a modern consumer unit is not to touch it, so call a registered electrician.
Bathroom lights and other wet areas
Bathrooms present a much higher risk of electric shock because water conducts electricity easily. For this reason, all circuits in or passing through bathrooms or shower rooms are required to be protected by an RCD. When planning bathroom electrical zones, enclosed ceiling lights are preferable to light fittings that hang down.
Unenclosed light fittings should be out of reach of someone using the bath or shower. A ceiling-mounted pull-cord switch is a better option than a wall switch.
Moisture in a bathroom or outside fitting on the same circuit is one possible cause of a lighting circuit tripping, so a bathroom light that keeps failing is worth having checked by a registered electrician.
Warning signs that mean stop and call an electrician
A light that simply refuses to turn on is an inconvenience, but certain visual and audible symptoms indicate a serious electrical hazard. Flickering lights should not be ignored as it can be a sign that your electrical installation needs to be inspected by a registered professional.
You should leave the light switched off and contact a competent registered electrician if you notice any of the following warning signs:
- Visible damage to plugs or sockets in the room
- Burn marks or cracking around light fittings and switches
- Crackling noises or a buzzing sound from the hardware
- Switches or fittings that feel unusually warm or hot to touch
- Circuit breakers repeatedly tripping or blown fuses
- Flickering lights across the room or house
These symptoms require professional attention immediately. If there is a strong smell of burning, visible sparking or you receive an electric shock, switch off the electricity at the main switch if it is safe to reach. You must call the emergency services on 999 for a fire or a serious electric shock, and call 105 if you experience a general power cut in your area.
What an electrician does when a light will not work
When you hire an electrician for a broken light, they will start by fault finding. They will test the circuit to find which part has failed. Once they find the fault, they will explain the problem and either repair the connection or replace the broken component.
In England and Wales, electrical work in homes is covered by Part P of the Building Regulations. The national wiring standard that electricians work to is BS 7671, often called the Wiring Regulations. In England, most repairs, replacements and maintenance jobs are not notifiable to building control.
However, installing a complete new circuit is notifiable. Adding a lighting point to an existing circuit is notifiable only in special locations. In England, these special locations are the spaces around baths and showers, while in Wales, special locations also include kitchens and outdoors.
Electricians registered with a government-authorised competent person scheme, for example NICEIC or NAPIT, can self-certify this notifiable work. After notifiable work, the customer should receive the electrical certificate and a Building Regulations compliance certificate. For non notifiable work, the electrician should provide a Minor Works Certificate.
How electricians charge for lighting repairs
Small jobs and fault finding are usually charged by the hour, often with a call-out fee or a minimum charge that covers the first hour. If your light fails in the evening and you require an urgent repair, keep in mind that out-of-hours work carries a premium rate. London and the South East cost noticeably more for electrical services than other parts of the UK.
If the fault needs a larger job, the electrician will provide a price for it. Defined jobs are usually quoted as a fixed price based on the property size, the number of circuits, access to the wiring and the specification of the new fittings.
A quote is a fixed price, whereas an estimate is not and can change as the work progresses. Before agreeing to proceed, you should check what the quote includes, as it may or may not include VAT, materials, certification, and making good any damaged plaster and decoration. Under the Consumer Rights Act 2015, a service must be carried out with reasonable care and skill, and the customer can ask for poor work to be put right at no extra cost.
Services arranged at home, by phone or online usually carry a 14-day cooling-off period. This does not automatically apply to urgent repairs the customer has explicitly asked for. You can consult Citizens Advice for guidance on your own specific situation.
Common problems when hiring for electrical faults
When you are left in the dark, it is tempting to book the first available person, but choosing on price alone is one of the common problems customers face. You should watch out for emergency call outs with no price given before attendance, which can result in an unexpectedly high bill. Be wary of tradespeople who demand large cash deposits before starting work and provide no paperwork.
Another frequent issue is unregistered work with no certificate and no notification to building control when it is legally required. You should always check the electrician is registered with a competent person scheme before they arrive. Vague quotes that leave out making good, certification or VAT are also common, as these hidden extras will inflate the final cost.
Sometimes, what starts as a simple fault finding visit escalates unnecessarily. A common problem customers face is being told a full rewire or a new consumer unit is compulsory with no test evidence provided. Unscrupulous operators may also use very cheap initial inspections to sell long lists of remedial work, often presenting minor advisory items on an Electrical Installation Condition Report, or EICR, as outright failures.
What to tell an electrician before the visit
Providing clear information before the electrician arrives helps them bring the right parts and diagnose the fault faster. Start by describing exactly what has stopped working and whether it is a single light, a whole room, or the entire floor. Tell them about any steps you have already taken, such as changing the bulb or pressing the RCD test button.
You should give the electrician the following details when you call:
- Exactly which lights have stopped working
- Whether you have already fitted a new bulb of the correct type
- Any recent attempts to change a light fitting or switch yourself
- Any warning signs you have noticed, such as flickering or crackling
- Whether your consumer unit has older rewireable fuses or modern circuit breakers
Be honest if you have recently tried to change a light fitting yourself, as this gives them an immediate starting point for their diagnostic checks. Details about a smell of burning, a warm switch or a circuit that keeps tripping are all useful for the electrician to know.
Common questions
Why is my light switch not working?
A loose connection at a switch is one possible cause. If the switch feels warm or makes a crackling sound, switch the light off and call a registered electrician.
Why is my ceiling light not working but the bulb is fine?
When a new bulb does not solve the problem, the cause may be the fitting, a loose connection at the ceiling fitting or an LED driver or transformer. Do not remove the fitting to investigate, as that is work for a registered electrician.
Why are my downlights not working?
If a single downlight is off, the lamp may have failed. If a group of downlights stops working at once, an LED driver or transformer is one possible cause. Downlights can also overheat, so you should check the fittings for discolouration or scorched labels.
What causes a bathroom light to stop working?
Moisture in a bathroom fitting on a lighting circuit is one possible cause of the circuit tripping. Enclosed ceiling lights are preferable in bathrooms to ones that hang down, and an electrician can advise on your fittings.
Next steps
When a light stops working, you can safely check the bulb and press the RCD test button before calling a professional. Keep this checklist in mind as you investigate the problem:
- Switch the light off and wait a few minutes for the old bulb to cool before changing it.
- Verify the replacement bulb is the exact type specified and does not exceed the maximum power rating.
- Press the test button on your RCD to check it functions, but do not repeatedly reset a tripping circuit.
- Look for serious warning signs such as burn marks, crackling sounds or hot switches.
- Leave the light switched off and contact a competent registered professional if a new bulb does not work.
Electrical faults require professional testing to ensure your home remains safe. If you have ruled out the bulb and need a fault diagnosed, you can find an electrician near you to investigate the circuit safely.
Find a top rated electrician near you
5,057 electricians across the UK, each ranked on their Google rating and the number of reviews behind it. Start with your county: